Luyten Pijpwerk · Oosterhout

We make pipes one at a time and we sell them one at a time

Eighteen things live on this bench: flue pipes in four lengths, prepared oak and pine, cast sheet by the half metre and the tools that cut a mouth. No minimum order. Wijnand will answer the email himself.

Since
1974, two generations
Alloys poured
15, 30 and 50 per cent tin
Pipes a year
About 900
A hand holding small metal parts steady under a torch flame on a scorched soldering block.

Seaming a foot, Tuesday morning

From sand bed to rack board

Six things happen to every pipe we send out

  • 01

    Cast on sand

    Metal is poured onto a sand bed and comes off as a sheet with a skin. Thicker at the bass end, thinner at the top, planed by hand to the thousandth we marked.

  • 02

    Rolled and seamed

    The sheet goes round a mandrel and the seam is soldered in one pass. A good seam disappears. A bad one you hear for a century.

  • 03

    A mouth cut true

    The upper lip, the languid and the windway decide everything. Two tenths of a millimetre out and the pipe speaks late.

  • 04

    Voiced at the bench

    Every pipe speaks on the voicing machine before it leaves, at the wind pressure you send us. We note the pressure on the foot.

  • 05

    Timber quartered

    Oak and pine are cut through the heart so the boards move the same way in a dry church. We buy whole, saw whole, stack and wait.

  • 06

    Sent standing up

    Pipes travel upright in a crate with a rack board inside, the way they sit in the organ. Nothing arrives oval.

What the alloy does
The halving

Drop an octave and the pipe loses half its length

Turn the dial. The rank below is the same thirteen pipes every time, redrawn to the pitch you pick. Nothing is cropped and nothing is faked: eight foot C stands 2.44 m, and every octave down the keyboard takes exactly half of that away.

Top of the longest pipeRack board

Eight foot. Low C speaks at 2.44 m and the rank runs an octave to the right.

The ladder, priced

One voice, four lengths, and the wide flute beside it

These five sit on the bench today. Halve the length and the metal halves with it, but the mouth still takes the same morning, so the price never halves.

Rows of polished metal organ pipes, each with a mouth cut into its front, standing in a pale case.

Prestant rank

Prestant C, 8 foot

€615

Open flue pipe · 2.44 m speaking length · spotted metal, half tin

A close rank of tall metal pipes with their mouths cut in one straight line near the feet.

Prestant rank

Prestant c, 4 foot

€352

Open flue pipe · 1.22 m speaking length · spotted metal, half tin

Pale cream pipes seen from below, their rounded fronts running up out of the frame.

Prestant rank

Prestant c1, 2 foot

€214

Open flue pipe · 61 cm speaking length · spotted metal, half tin

Slim gilded pipes standing in a row on a carved wooden rail.

Prestant rank

Prestant c2, 1 foot

€139

Open flue pipe · 30.5 cm speaking length · spotted metal, half tin

Open-topped grey metal pipes of different heights standing side by side.

Prestant rank

Open Fluit c, 4 foot

€298

Open flue pipe, wide scale · 1.22 m speaking length · thirty per cent tin

Asked at the counter

Three questions we get every week

Anything missing from these three is usually a two-line answer. Write and ask.

Write to the bench
  • Send us the pipe, or the two either side of the gap. We measure the scale, the mouth width, the cut-up and the alloy, then make one that sits in the row without an argument. Most matches take four to six weeks. If the rank is a known hand, say Bätz or Witte, tell us and we will go and look at a surviving one first.

  • More tin means a brighter pipe and a dearer one. Half tin, what the trade calls spotted metal, is bright and keeps its shape in a tall body. Thirty per cent is quieter and warmer and costs a third less. Below about fifteen per cent the metal is soft and slow and we will only roll it for basses that sit on a rack board.

  • No. We make flue pipes, where the wind is cut at a mouth. A reed has no mouth: the air drives a brass tongue against a shallot inside the boot, and the cone above it only lengthens the sound. It is a different trade and we send that work to a reed voicer in Dongen. We do sell the bench tools for both.

A hand steadying a workpiece at a lathe while shavings fly off the cutter.

Turning a stopper, back bench

Statendamweg 14

Tuesdays the bench is open and you can stand right at it

Most of our customers want to hold the metal before they order it. Come and do that. There is a voicing machine by the window, there is coffee, and if you bring a pipe that has gone wrong, you will get a straight verdict on whether saving it makes sense.

Mariëlle voices, Kwinten casts, Wijnand answers the post. Between the three of us something is always speaking in the back room, so bring ear defenders if you are fussy.

Two hands filing a small metal part held in the jaws of a bench vice.A row of wooden-handled bench tools hanging in order on a rack.